Description
1. introduction
abb dcs is a distributed control system designed and developed by Swiss Asea Brown Boveri Company (abbreviated as abb company). It has a wide range of applications and can be used in discrete manufacturing industries
, such as machine tools, automobiles, aircraft manufacturing and other industries, as well as in large and medium-sized enterprises. Small-scale continuous production process industries, such as petroleum, chemical industry, thermal power units, steelmaking,
building materials and other industries. abb dcs system adopts international standards from hardware
design to software design and communication. The software programming language ampl (asea mas ter pi ece language) of abb dcs is a programming mode of the control system. This article introduces the architecture of abb dcs and its fieldbus network.
2 abb dcs distributed industrial control computer system architecture
abb dcs distributed control system uses advanced microprocessors (33mhz motorola 68020 and 33mhz intel 80386, 80486 chips), crt graphic display technology, high-speed safety communication technology and modern control theory to
form an on-site control station (mp200, ac410 , ac450 series and local and remote i/o series), operator station (as500 series), engineer station (master ai d series), information management system station (advant station series ), computer
and network interface station (master gate series), computer network (master bus series) and other computer communication equipment, it is a large-scale intelligent network with dispersed physical locations, dispersed system functions
, dispersed control functions, and centralized operation display management for process control and process decision-making management.
The communication network structure of abb dcs is divided into three layers:
3 Information Management Network Layer
It can be connected to 9 control networks. The network is composed of type mb300 bus, and the bus transmission rate reaches 10mbps.
4 Control network layer
The control network layer consists of 9 buses of type mb300. A control network may include 99 stations (including stations in local control networks). Each mp200/1 or ac450 station in the control network can be connected to a local control network.
A local control network can include 9 buses of type mb300. mb300 is a high-performance, serial, synchronous, half-duplex high-speed bus with large data volume. It adopts ieee 802.2 logical link control (llc) protocol and ieee 802.3 carrier frame listening
multiple access with conflict detection (csma/cd) media access control (mac) protocol. It is an ethernet type LAN and the bus
can carry loads . 45 nodes. When no repeater is used, the maximum communication node distance is 500m; when using 3 coaxial segments, 4 repeaters and 2 point-to-point links, the maximum communication node distance is 2500m, and the bus transmission rate is 10mbps.
mb300 realizes the connection to the host computer and communication with PLC systems such as MP200 through each node . It generally follows the 543 rule, that is, it is composed of 5 sections and 4 repeaters (repeater) connections, 3 of which can be
connected to equipment. It must be noted that only the marked prescription of the cable can be connected through the transceiver ( tranceiver ) Equipment, different equipment connections use different connection cables, such as tk526 cable to the pu510 operating station,
and tk576 cable to the control station. The tranceiver can only be installed at the 2.5-meter mark on the main cable section. The spacing between the tranceivers on the coaxial cable section between the two line joints should be an integer multiple of 25 meters. The connection method is as shown in the figure.
t1 and t2 are terminal resistors . As long as one end is grounded, the terminal resistance is 50 ohms. The mb300 bus is a coaxial cable. It is divided into thick cable, thin cable and optical cable. Their functions are different. When laying the coaxial cable, you need to
pay attention to it. Isolation from other signal cables, such as 30cm away from signal cables, 50cm away from 380v low-voltage cables, and 5m away from high-voltage cables. The mb300 bus uses the cs513 interface card. The three dial switches s1, s2, and s3 are
used to set the network number, node number, and protocol number respectively. The low four bits of s1 are used to set the master/slave station selection.
The high four bits are used to set the protocol number, s2 is used to set the node number, and s3 is used to set the network number. When it is necessary to modify or find out the cause of the fault through fault information, you can enter the engineering station to
modify the data or know the fault location of the mb300 bus through the fault code. Understand the communication factors that affect mb300 and analyze these factors one by one.
Excitation system ABB module DSQC1015
Excitation system ABB module DSQC1000
Excitation system ABB module DSPX3221
Excitation system ABB module DSPU131 3BSE000355R1
Excitation system ABB module DSPU120
Excitation system ABB module DSPC452 57310303-A
Excitation system ABB module DSPC406
Excitation system ABB module DSPC406
Excitation system ABB module DSPC365
Excitation system ABB module DSPC3221
Excitation system ABB module DSPC3122
Excitation system ABB module DSPC3121
Excitation system ABB module DSPC3001
Excitation system ABB module DSPC174 3BSE005461R1
Excitation system ABB module DSPC174
Excitation system ABB module DSPC173
Excitation system ABB module DSPC172H
Excitation system ABB module DSPC172H
Excitation system ABB module DSPC172-2
Excitation system ABB module DSPC172
Excitation system ABB module DSPC172
Excitation system ABB module DSPC171 57310001-CC
Excitation system ABB module DSPC171
Excitation system ABB module DSPC170H
Excitation system ABB module DSPC170
Excitation system ABB module DSPC170
Excitation system ABB module DSPC157
Excitation system ABB module DSPC155
Excitation system ABB module DSPC154
Excitation system ABB module DSPC153
Excitation system ABB module DSPC-150
Excitation system ABB module DSPB120
Excitation system ABB module DSPB112
Excitation system ABB module DSPB110
Excitation system ABB module DSPA110
Excitation system ABB module DSO14
Excitation system ABB module DSMD113 5736045-N/1
Excitation system ABB module DSMD113
Excitation system ABB module DSMD112
Excitation system ABB module DSMD110
Excitation system ABB module DSMC112 57360001-HC
Excitation system ABB module DSMC112
Excitation system ABB module DSMB340
Excitation system ABB module DSMB178
Excitation system ABB module DSMB176
Excitation system ABB module DSMB175 57360001-KG
Excitation system ABB module DSMB175 57360001-KG
Excitation system ABB module DSMB-175
Excitation system ABB module DSMB175
Excitation system ABB module DSMB173
Excitation system ABB module DSMB151
Excitation system ABB module DSMB144
Excitation system ABB module DSMB137
Excitation system ABB module DSMB133 57360001-CY
Excitation system ABB module DSMB133
Excitation system ABB module DSMB127 57360001-HG
Excitation system ABB module DSMB127
Excitation system ABB module DSMB-126A
Reviews
There are no reviews yet.